This is an inexpensive and heavy-duty Timer and Temperature metal control panel for electric Oven Kiln. The PID controller is one set point temperature controller and the timer has 2 cycles (T1, T2) that can be used for operation time. According to your kiln, you need to select 30Amp, 40Amp or 50Amp.

It comes with a thermocouple (maximum 2372 F) and TC connector that you can easily change your thermocouple and if you need to change your sensor to a specific one, I can change it for you too.

Press the ON/OFF switch, it will reset the timer and start another curing batch. During the heating process, one can use a manual switch to turn ON or OFF the element power if needed. The alarm buzzer can be used as either a temp alarm or a set point finishing alarm. It can also be muted.

If you need any other control switch please contact us. 

 
Features:

• Powder-coated wall-mount metal enclosure box.
• Dual-line display one set point PID temperature controller.
• According to your kiln, you need to select 30Amp, 40Amp, or 50Amp.
• Timer with 2 time cycles T1 and T2
• There are ON/OFF switches for stopping or resetting operations. You can reset the process by pushing the timer set key once and waiting for 6 seconds.
• Buzzer Alarm and alarm mute switch.
• 2 Solid State Relay and heatsink and fans for cooling the heat inside the box.
• Oven temperature probe with male and female connector.
• 4 Glands for connecting input and output cable, thermocouple, and one extra output  
• The breaker switch for overload protection and emergency completely cut off power to the panel.
• Adaptor 12V for Fans and timer or other extra applications.

You can reset the process by pushing the timer set key once and waiting for 6 seconds.

Description:

The oven can be heated up to the set point by the PID temperature controller as soon as possible and maintained for a pre-set period to cure the part. When the batch is finished, the coating process can be restarted again by pressing the ON/OFF button.

The sensor provided in this control panel can handle up to 1832 degrees F.  The base of the probe has a screw and nut for easy mounting on the Oven. The probe is 6" long and 0.2” (5.0 mm) in diameter and made of stainless steel with a plated brass base. The default sensor + connector cable length is 6 ft (2m).

Specifications

 Note:

• The control panel is designed for North American 240V AC power lines which require four line power connections (L1, L2, Neutral, and Ground). Please verify your power supply before purchase.
• This control system is designed for heating elements (resistive load) only, not for gas burners or propane heaters. If you want to use the system for a gas burner please check the following link,

• Input power cord (SOOW 10/4) is not included because each user may have different hook-up requirements.
• The heating element is not included.

Timer Modes:

P1 = 0 (Single delay with no cycle or loop): Only there is one timer T1. The relay stays disconnected (off) when T1 is counting and will become connected (on) once T1 finishes counting.

P1 = 1 (Single delay with no cycle or loop): Only there is one timer T1. The relay stays connected (on) when T1 is counting and will become disconnected (off)  once T1 finishes counting.

P1 = 2 (Dual timer delay T1, T2 with no cycle or loop): The relay stays disconnected (off) when T1 is counting and will become connected (on) once T2 is counting and will be off when T2 finishes counting.

P1 = 3 (Dual timer delay T1, T2 with no cycle or loop): The relay stays connected (on) when T1 is counting and will become disconnected (off) once T2 is counting and will be on when T2 finishes counting.

P1 = 4 (Dual timer delay T1, T2 with cycle or loop): The relay stays disconnected (off) when T1 is counting and will become connected (on) once T2 is counting and it will repeat this cycle.

P1 = 5 ((Dual timer delay T1, T2 with cycle or loop): Relay stays connected (on) when T1 is counting and will become disconnected (off) once T2 is counting and it will repeat this cycle.

PID Temperature controller :

High Measuring accuracy, ±0.2% or ±1 unit of full input range, Decimal point function, percentage of output,

Calibration function, Celsius or Fahrenheit display, HY (differential gap), Alarm HY, ....